| Partea Nu | Producător | Cerere |
|---|
| MAX6314US50D1-T | MaximIC | 68H11/bidirectional-compatible microprocessor reset circuit. Reset threshold(nom) 5.00V. Reset timeout period(min) 1ms. |
| MAX6317HUK39AX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 3.900V, min reset timeout 1ms, typ watchdog timeout 102ms |
| MAX128BCAI | MaximIC | Multirange, +5V, 12-bit DAS with 2-wire serial interface. INL(LSB) +1,-1 |
| MAX213ECAI | MaximIC | +-15kV ESD-protected, +5V RS-232 transceiver |
| MAX6314US42D4-T | MaximIC | 68H11/bidirectional-compatible microprocessor reset circuit. Reset threshold(nom) 4.20V. Reset timeout period(min) 1120ms. |
| MAX519BCSE | MaximIC | 2-wire serial 8-bit dual DAC with Rail-to-Rail outputs. TUE(LSB) 1.5. |
| MAX6105EUR-T | MaximIC | Low-cost, micropower, low-dropout, high-output-current, SOT23 voltage reference. Output voltage 5.000V, input voltage range (Vout + 200mV)V to 12.6V to 12.6V. |
| MAX706RESA | MaximIC | Low-cost, microprocessor supervisory circuit. Precison supply-voltage monitor 2.63V. Active-low reset output signal. |
| MAX4305ESA | MaximIC | Low-noise, low-distortion op amp. Bandwidth 340MHz. Minimum stable gain 10V/V. |
| MAX4187EEE | MaximIC | =1. |
| MAX909CSA | MaximIC | Quad, high-speed, ultra low-power, single +-5V supply operation TTL comparator. Internal latch. |
| DG307AC/D | MaximIC | CMOS dual and quad analog switch. |
| MXD1013SE015 | MaximIC | 3-in-1 silicon delay line. Output delay 15ns. |
| MAX442CPA | MaximIC | 140MHz unity-gain bandwidth, 2-channel video multiplexer/amplifier. |
| MAX263AEPI | MaximIC | Pin programmable univesal and bandpass filter. Accuracy 1%. |
| MAX6307UK43D4-T | MaximIC | Multiple-input, programmable reset IC (open-drain reset output,factory-set reset threshold on Vcc,1additional undervoltage reset input,negative/overvoltage reset inp.).Factory-trimmed reset thresholds4.193(min),4.408(max).Nominal timeout period 1120ms. |
| MAX3664E/D | MaximIC | 622Mbps, ultra-low-power, 3.3V transimpedance preamplifier for SDH/SONET. |
| MAX4420CPA | MaximIC | High-speed, 6A single MOSFET driver. 4.5V t0 18V supply range. |
| DG308AAK | MaximIC | Quad, SPST, NO analog switch |
| MAX6321HPUK40BZ-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 4.000V, reset timeout(min) 20ms, watchdog timeout(typ) 25.6sec |
| MAX6317HUK32BZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 3.200V, min reset timeout 20ms, typ watchdog timeout 25.6sec |
| DG309DY | MaximIC | Quad, SPST, NC analog switch |
| MAX6333UR20D3-T | MaximIC | Ultra-low-voltage, low power microprocessor reset circuit. Reset threshold(typ) 2.0V, reset timeout(min) 100ms. Standard version |
| MAX7219ERG | MaximIC | Serially interfaced, 8-digit LED display driver. |
| MAX8873SEUK-T | MaximIC | Low-dropout, 120mA linear regulator. Preset output voltage 2.84V. |
| MXD1013SA060 | MaximIC | 3-in-1 silicon delay line. Output delay 60ns. |
| ICL7611BCTV | MaximIC | Single operational amplifier,5mV |
| MAX136CJL | MaximIC | Low power, 3 1/2 didit A/D converter with display hold |
| MAX6306UK26D3-T | MaximIC | Multiple-input, programmable reset IC (open-drain reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual reset input). Factory-trimmed reset thresholds 2.564(min),2.696(max) Nominal timeout period 140ms. |
| MAX6312UK38D2-T | MaximIC | Multiple-input, programmable reset IC(push/pull reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual-reset input). Factory-trimmed reset thresholds 3.705(min) 3.895(max). Nominal timeout period 20ms. |
